Product Summary
Chevy Small Block V8, Dual Plane Intake Manifold Type
- Edelbrock Performer Series 4 barrel carbs have proven themselves to be easy to tune with great drivability
- Bolt-on-and-run performance right out of the box
- For small-block Chevy engines operating from 1500 to 6500 RPM
- Camshaft features Maximum Power in High-RPM with Good Low-End Torque – More Lift and Duration than Most Street Camshafts
- All Edelbrock products are proudly made in the U.S.A.
Installation Tips !
- Installation Notes: Use #8504 Edelbrock bolt kit. Recommended intake gasket: Edelbrock #7201.
- Manifold height: A-4.20″, B-5.25″ see A/B Measurements Guide (Link).
- Port exit dimensions: 1.16″ x 1.92″.
Details
Top off or upgrade your Small Block Chevy with these top end Performer Packages from Edelbrock.
Kit Includes:
- (1) Edelbrock 7101 Performer RPM Intake Manifold, Plain Aluminum Finish
- (1) Edelbrock 1407 Performer 4 Barrel Carburetor, 750 CFM, Manual Choke
- (1) Edelbrock 7102 Performer RPM Camshaft/Lifter Kit, SB Chevy
Edelbrock 7101 Performer RPM Intake Manifold
- Dual-plane, high-rise intakes with 180° firing order to produce incredible top-end horsepower while retaining good throttle response
- Larger plenums and runners match the free-flowing exhaust, high-lift cams and other modifications of a high output engine
- Intended for high-performance street or competition engines that run up to 6500 rpm
- Not recommended for emissions equipped engines
- Chevrolet 262-400 Small-Block V8
- PERFORMER RPM (1500-6500 rpm)
- Designed for 1955-86 262-400 c.i.d. Chevy V8s for maximum power and a broad torque curve for high-performance street/marine
- Provides power like a single-plane and throttle response like a dual-plane
- Has provisions to add oil fill tube
- No provisions for exhaust heated or stock-style choke
- Accepts late-model waterneck, air-conditioning, alternator and H.E.I.
- Will fit cast iron Chevrolet Bowtie heads, but will not fit 1987 and later cast iron heads
- Will not fit under stock Corvette hood
Edelbrock 1407 Performer 4 Barrel Carburetor, 750 CFM
- Whether you need to replace an aging stock carb or are looking for a performance carb to top off your hot rod, Edelbrock Performer Series carbs are the best choice for performance and value
- All Edelbrock parts are proudly made in the U.S.A.
- 750 CFM 4 barrel carburetor
- Designed and calibrated for optimum street performance in small-block and big-block engines with Performer RPM, RPM Air-Gap and Torker II manifolds and with Performer manifolds on large cubic-inch engines
- Includes manual choke and detailed instructions
- Ford/Mopar throttle adapter arms sold separately
- Manual choke
- Bolt-on-and-run performance right out of the box
- Smooth throttle response throughout the power band
- Uses metering rods to transition between circuits – rods can be changed in seconds without carburetor removal or draining fuel
- Float levels are factory set; adjustments are rarely needed
- Change jets, adjust floats & replace needles/seats without draining fuel or removing carb
- Two-piece design means no gaskets below the fuel level for leak-free operation
- Lightweight all-aluminum body is compatible with gasohol and blended fuels
- Includes both timed and full vacuum ports for ignition advance
Comes with:
- Metering Jets – Primary .113, Secondary .107
- Metering Rods – .071 x .047
- Step-Up Spring – orange (5″ Hg)
Edelbrock 7102 Performer RPM Camshaft/Lifter Kit
- Designed for 1500 to 6500 Performance
- Maximum Power in High-RPM with Good Low-End Torque
- Matched to Edelbrock Performer RPM Intakes
- 10 to 12 in. of Manifold Vacuum at Idle
- More Lift and Duration than Most Street Camshafts
- Includes Hydraulic Lifters and Assembly Lube
- Dyno Matched/Street Proven Performance
- Take The Guesswork Out Of Camshaft Selection
Charts
-
325-7101 Instructions (PDF)
-
3257101 Power Graph (Link)
-
Installation Instructions (PDF)
-
Edelbrock 750 CFM 4 Barrel Carburetor Installation Instructions (PDF)
KEY SPECS |
|
---|---|
Brand | Edelbrock |
Intake Manifold Type | Dual Plane |
Carburetor Quantity | One |
Carburetor Barrels | 4-Barrel |
CFM | 750 CFM |
GENERAL |
|
Carburetor Flange Type | 4-Barrel Square Bore |
RPM Range | 1,500-6,500 |
Intake Manifold Fasteners Included | No |
Sold in Quantity | Kit |
Reviews
There are no reviews yet.